Leave Your Message
News Categories
Featured News

Application of Distribution Transformer

2026-10-04

The application of distribution transformer is the last medium-voltage drop to customer voltage near the load, at the end of a primary feeder. Walk the last pole or pad first, then match voltage and kVA, then choose mounting. Later sections locate a bulk power transformer so it is not mixed into this job, and they show when a printed 6–10 kV oil-immersed unit belongs.

ANDELI 6-10 kV oil-immersed distribution transformer tank used for near-load feeder applications

Overhead laterals hang a pole-mounted transformer at the end of the primary. Underground or public-street work puts a pad-mounted transformer in a locked ground cabinet beside the same feeder.

Voltage and kVA Jobs That Count as Distribution Work

Typical jobs are medium voltage in the low tens of kV down to building voltage; frequency follows the grid, and an ANDELI inquiry must state frequency rather than assume a printed 50 Hz or 60 Hz nameplate. The useful scan is which feeder you are on, not a single global kVA cartoon.

Independent education texts give IEC-style step-down examples of 11 kV, 6.6 kV, or 3.3 kV down to 415 V, 400 V, or 230 V. North American laterals often sit near 12.47 kV or 13.8 kV, with 120/240 V split-phase at the house.

Primary distribution in those overviews is often around 11 kV, with a published working range of 2.4–33 kV for large consumers. Secondary work is the utilization run to homes and shops; the same texts note 50 Hz or 60 Hz by region, which is a grid fact, not an ANDELI listing.

Printed ANDELI S11 6–10 kV series distribution rows use HV combinations of 11 kV, 10.5 kV, 10 kV, 6.3 kV, and 6 kV stepping down to 0.4 kV. Those rows cover rated capacity from 30 kVA to 2500 kVA.

International power-transformer general requirements live in IEC 60076-1; ANDELI prints GB 1094 family standards on this series rather than an IEC 60076 listing. Keep those two families next to each other instead of silently equating them.

Because the unit stays energized all day, independent texts often discuss maximum efficiency around 50–75% of full load. That all-day iron-loss design is why a lightly loaded residential can is still a distribution job, not a spare substation transformer.

Job scan Independent examples Printed ANDELI S11 distribution US DOE specifier language
Network place End of primary, service voltage to customers Power distribution system application line Coverage definition, not a siting map
HV class 11 / 6.6 / 3.3 kV examples; NA 12.47 / 13.8 kV 11 / 10.5 / 10 / 6.3 / 6 kV Input ≤34.5 kV
LV / utilization 415 / 400 / 230 V; 120/240 V split-phase 0.4 kV Output ≤600 V; 60 Hz
kVA band Teaching texts vary; do not freeze one cutoff 30–2500 kVA Liquid-immersed 10–5000 kVA on Cornell LII
Frequency 50 Hz or 60 Hz by region Order field; not printed on those S11 rows Rated 60 Hz in 10 CFR 431.192

Who the Unit Serves: Houses, Campuses, Plants, and Rural Laterals

Urban pads may feed many premises; rural cans may feed one farm; large plants may own several units or take primary service. That is the real map behind generic distribution transformer applications lists that only name homes, malls, and factories.

A single-phase overhead unit in Iowa State notes typically feeds one to eight residences. Crew language still calls that small overhead can a pole pig, while a larger pad on a housing estate can feed a whole street.

Rural laterals often put one tank per farmyard or pumping station. Urban streets share one pad among several customers; a campus or mill may park several oil tanks, each feeding a building or process board.

Where are distribution transformers used on a primary-metered site? The customer may own a basement or yard step-down while the utility meters the medium-voltage service. That ownership split does not change the electrical job: it is still the last drop to utilization voltage.

Industrial shops also run utilization-level kVA jobs, not only 11 kV to 0.4 kV cartoons. Grounding and motor or drive loads still decide whether that shop transformer is the right object; they do not by themselves turn it into a transmission unit.

Pole, Pad, Indoor Dry, or Restricted-Yard Placement

Overhead laterals use pole-mounted tanks; public or underground sites use pad-mounts; fire-sensitive indoor rooms use dry-type; fenced yards may use substation-class tanks. Mounting follows access, fire, and how the feeder is built, not a catalog beauty contest.

A pole-mounted and pad-mounted distribution transformer pair is the everyday choice on the same voltage class. Pole-mounted transformer work hangs the tank on overhead construction; pad-mounted transformer work sits a locked cabinet on a concrete pad where underground cables or public access make a bare tank a poor neighbor.

Sealed oil-immersed distribution transformer tank on skids, the outdoor liquid-filled form used on many plant pads

Placement Typical feeder / site Why it fits Poor fit
Pole-mounted Overhead primary, rural or street laterals End-of-primary can on the pole Underground streets, tight public sidewalks
Pad-mounted Underground or public-access sites Locked cabinet, tamper-resistant Restricted yards that want open gauges and fans
Indoor dry-type Hospitals, schools, indoor rooms No large oil tank in the occupied building Outdoor utility laterals that expect a liquid tank
Restricted-yard / substation-class Fenced plant or campus yard Close-coupled switchgear, accessible devices Unfenced public pads

Why This Job Is Not a Power-Transformer Assignment

Near-load variable-load final step-down is distribution work; bulk transmission or large substation transformation is a different assignment. If a search result asks for the difference, treat this paragraph as a locator, then stay on feeder placement.

A power transformer in that locator sense lives on the transmission or large-substation side, often with extra cooling stages and a job of moving bulk energy rather than serving one street or one plant board. The near-load unit on a transformer feeder is still the distribution object even when its kVA is larger than a backyard can.

Classroom notes sometimes group units at or below 1000 kVA as distribution transformers close to loads, and larger OA/FA tanks as substation power transformers. Printed ANDELI distribution rows still run through 2500 kVA, so treat that 1000 kVA line as teaching language, not a law that voids the larger distribution rows.

Matching a 6–10 kV Oil-Immersed ANDELI Unit to the Job

Use the printed S11 distribution family when the job is an oil-filled near-load step-down on a 6–11 kV-class feeder to 0.4 kV, then state frequency and connection group on the inquiry. Indoor fire-sensitive rooms, US DOE-listed 60 Hz coverage paperwork, and the separate higher-LV power-transformer rows are different jobs.

The 6-10 kV series oil-immersed distribution transformer is printed as widely used in power distribution systems. Features called out with that family include a cold-rolled silicon-steel core, a fully sealed tank, oxygen-free copper windings, and a Dyn11 connection printed to reduce harmonic impact on the grid.

Printed connection groups on the S11 distribution rows are Dyn11, Yzn11, and Yyn0, with Dyn11 and Yyn0 from 630 kVA. Low-voltage windings through 500 kVA use a double-layer cylindrical structure; 630 kVA and above use double-helix or four-helix, while high-voltage windings use a multi-layer cylindrical structure.

Printed impedance is 4.0% through 500 kVA, 4.5% from 630 kVA to 1600 kVA, and 5.0% at 2000 kVA and 2500 kVA. High-voltage taps are printed as ±5% or ±2×2.5%.

Printed transformer standards on that series are GB 1094.1-2013, GB 1094.2-2013, GB 1094.3-2017, GB 1094.5-2008, GB/T 6451-2015, GB 7595-2017, GB/T 25289-2010, and GB 3837-2016. The live series does not print UL, IEEE, DOE, or NETA listings.

Normal printed service is altitude below 1000 m, highest air +40 °C, highest daily average +30 °C, highest annual average +20 °C, and lowest outdoor −25 °C. Special service covers altitude above 1000 m or air above +40 °C, and the inquiry must state frequency along with model, kVA, HV/LV, taps, phases, and connection group.

ANDELI 6-10 kV series oil-immersed distribution transformer product photograph