Leave Your Message
News Categories
Featured News

How to Tell the Types of Dry Type Transformer Apart

2026-09-21

A dry-type transformer keeps the core and coils in air or a solid compound instead of oil, and the types of dry type transformer a buyer has to tell apart are cast resin, VPI, and open-wound. The phrase what is dry type transformer names that same category: the medium around the coils, not the cabinet and not the voltage class. An EPC who reads “dry-type” on a one-line still has to name the winding before the spec is real.

Indoor room showing a cast-coil unit beside an unbranded varnished coil and an open-wound coil

The installed unit is a cast-coil example. The two coils on the cart are unlabeled samples, not extra catalog models.

Contents

  • Types of Dry Type Transformer Start With the Winding
  • Cast Resin, VPI, and Open-Wound Are Different Coils
  • VPE Is Not a Settled Fourth Winding Type
  • Enclosure and Cooling Are a Separate List
  • Voltage Class Does Not Choose the Coil
  • How to Tell Cast Resin, VPI, and Open-Wound Apart
  • Where the 6–10 kV SCB Page Sits
  • FAQ
  • References

Types of Dry Type Transformer Start With the Winding

A dry-type unit keeps its core and coils in air or a dry compound, and that category still holds more than one winding construction.

The shared fact is the missing oil bath. Heat and dielectric stress are handled by air, by a solid compound, or by both, while the copper can still be built in more than one way. Two data sheets can both say dry-type and still describe different coils.

Cast resin, VPI, and open-wound are those coil recipes. A ventilated shell, a sealed shell, or a medium-voltage label can be paired with more than one of them. The transformer category is the parent list for this equipment, and one resin-insulated series on that list is the example at the end.

People mix the names because a data sheet prints the winding, the cabinet, and the voltage on the same line. The winding decides how the copper is sealed. The cabinet decides how room air reaches that copper.

A buyer who stops at the word dry-type will price the wrong coil for a dusty or humid room. Naming the winding first keeps that mistake out of the purchase order.

Cast Resin, VPI, and Open-Wound Are Different Coils

Cast resin is a solid encapsulated coil, VPI is varnish forced into a coil that still breathes, and open-wound leaves the turns exposed to air.

Cast resin coil block, vacuum-pressure impregnated winding, and open-wound coil side by side

The three shapes are the coil itself. Cabinet doors are a later choice.

Dry-type windings, when the liquid is left out, are protected by cast-resin encapsulation or by vacuum-pressure impregnation with varnish. That split is the one named under power transformer insulation. Open-wound sits beside those two as the air-cooled coil the cast construction replaces.

Important: Solid-cast windings are fully encapsulated in a thermosetting resin, typically epoxy, and that construction is the alternative to an air-cooled open winding. The wording comes from the solid cast topic note, and it stays separate from any series test report.
Winding What the coil is What to ask Usual room match What it is not
Cast resin A cured solid block, typically epoxy, with the turns buried Is the winding a void-free solid, or can air still move through it? Humid, dusty, or corrosive indoor air, where a sealed coil is the point A cabinet style, a voltage class, or a light varnish dip
VPI Varnish driven in under vacuum and pressure; outer surface sealed; structure still semi-open Was the coil impregnated, and does it still ventilate? Indoor commercial or industrial rooms, including sheltered sites Full encapsulation, and not the same object as a cast block
Open-wound Turns left exposed under a lighter dip-and-bake varnish so air can cool them Can you see the winding, and is the room clean and dry? Cleaner indoor rooms A cast coil, or a recipe written for wet outdoor air

A cast resin transformer is the solid end of that table. Resin is poured, cured, and left as a dimensionally stable block. Looking at the coil, you see the block, not copper with daylight between the turns.

Calling that middle coil “sealed” on a purchase order hides the difference a cast block would have made. Varnish or resin is absorbed under vacuum and pressure, the outside looks closed, and the winding is still ventilated.

An open-wound transformer is the exposed case. Dip-and-bake varnish holds the turns, and the spaces between them are there for air.

Practitioners describe open-frame windings as prone to taking up moisture. That remark stays shop language, without a measured failure rate.

Cost follows the same order in specifier talk. A cast coil is treated as the expensive, moisture-resistant choice.

A varnished open coil is treated as the cheaper one, and it belongs in cleaner air. Those remarks still lack a price list.

VPE Is Not a Settled Fourth Winding Type

Some guides add vacuum-pressure encapsulated as a thicker coat than VPI, but the notes do not agree on the material or on whether that coat is really a cast coil.

One commercial explainer treats a VPE transformer as a heavier coating than VPI, and it points that coating at semi-outdoor, coastal, or moderately harsh rooms. On that page, VPE is a fourth construction name next to cast resin and VPI.

A practitioner note draws the line differently. There, VPE means silicone varnish, VPI means polyester varnish, and a named cast system stays cast resin rather than VPE.

Coated is also kept apart from cast. The two notes cannot both be the definition.

Ask a narrower question than the label. Is the coil in front of you a solid cast block, or a heavier varnish coat that still has structure you can ventilate?

If the answer is the solid block, you are back in the cast column. If the answer is a thick coat, you are still in an impregnation discussion, and VPE has not become its own settled family.

Enclosure and Cooling Are a Separate List

Vents, a potted shell, and a sealed cabinet describe how air and heat move. They do not say whether the coil was cast, impregnated, or left open.

Ventilated dry-type cabinet beside a sealed nonventilated cabinet

One cabinet is open to room air through mesh. The other keeps room air off the coils. The coil recipe is still a separate question.

A builder on the Arduino forum, with a small AC-to-5 V transformer and no case, asks whether a heat-shrink tube or a liquid compound should cover it. That question is about the shell, not about whether the winding was cast, impregnated, or left open.

A ventilated enclosure lets room air, or fan air, pass through openings and over the coils. Natural air and forced air both live on this cooling list. Either one can sit in front of a cast coil, a VPI coil, or an open coil.

An encapsulated or potted transformer encloses the windings in a solid mix such as resin, gravel, sand, or epoxy inside a shell. On a photo, that fill can look like a cast coil. The data sheet is describing the enclosure fill, and the winding family still has to be named on its own line.

TENV means totally enclosed non-ventilated. In the US definition, a nonventilated transformer is built to prevent external air circulation through the coils while operating at zero gauge pressure.

Heat leaves through the shell. The shell is chosen when the room air is conductive, corrosive, or combustible. That choice is about the air path, rather than epoxy versus varnish.

Axis Example labels What the axis decides What it leaves open
Winding construction Cast resin, VPI, open-wound How the copper is sealed or left in air Cabinet vents and the legal voltage band
Enclosure and cooling Ventilated, encapsulated, TENV, natural air, forced air How room air and heat move Whether the coil is a solid block
US voltage definition Low-voltage dry-type, medium-voltage dry-type Which legal voltage band the primary falls in The winding recipe

A buyer who treats “ventilated” as a winding type will accept an open coil inside a vented box and think the type question is finished. The box only told you the air path. The coil question is still open.

Voltage Class Does Not Choose the Coil

US rules split dry-type units into a low-voltage band and a medium-voltage band, and that split does not choose a winding family.

A low-voltage dry-type, in 10 CFR 431.192, has an input voltage of 600 V or less and keeps the core and coil in a gaseous or dry-compound insulating medium.

A medium-voltage dry-type, in that same definition, has a rated primary voltage between 601 V and 34.5 kV, again with the core and coil in a gaseous or dry-compound medium.

The distribution-transformer definition used for the efficiency program covers dry-type units from 15 kVA to 5000 kVA at 60 Hz, with input of 34.5 kV or less and output of 600 V or less, and it excludes a nonventilated transformer along with an autotransformer, a drive isolation transformer, a grounding transformer, a machine-tool transformer, a rectifier transformer, and a regulating transformer.

That kVA band is a legal boundary for the efficiency program. It does not assign a winding, and it does not approve or reject any one published series. A primary that falls inside the medium-voltage numbers can still be cast, impregnated, or open-wound.

How to Tell Cast Resin, VPI, and Open-Wound Apart

Ask whether the coil is a solid block, an impregnated winding that still ventilates, or an exposed varnished winding, then match that answer to moisture and dirt in the room.

Engineer checking dry-type coil construction against a specification in an electrical room

The sheet in that check should name the coil. A voltage and a cabinet code are not substitutes for it.

Dry type transformer applications in this check are the room itself: clean indoor air, dust, or humidity. A buyer (EPC / facility) can run the check without a factory tour.

  • Ask if the winding is a solid block. That answer is cast resin.
  • Ask if varnish was forced in and the winding still breathes. That answer is VPI.
  • Ask if the turns are exposed under a light varnish. That answer is an open winding.
  • Then match the answer to the room. Humid or dirty air argues for the solid coil. A clean indoor room is where the exposed winding is usually discussed.

Practitioners treat a cast coil as the costly, moisture-resistant choice, and they describe open windings as the ones that take up moisture. The same conversations keep VPI with indoor duty. Outdoor gear still has exposed bus and taps, which is why some specifiers leave VPI indoors and look at a cast coil when the room is dirty.

A cheaper open winding in a dusty or humid plant room is the mismatch those notes are about. The coil can be the lower quote and still be the wrong construction for that air. Cost and moisture are the only comparisons those notes actually make.

Where the 6–10 kV SCB Page Sits

The published 6–10 kV SCB page describes an epoxy and glass-fiber high-voltage coil, which is a cast-style example, while a separate SC(B)10 paragraph names a NOMEX paper system and the two descriptions stay apart.

Published Andeli SCB series dry-type transformer with cast-style coils

The photograph is the published cast-style unit. Open-wound and VPI models are outside what this photograph shows.

Andeli’s 6–10 kV SCB series dry-type transformer is an indoor distribution unit. The high-voltage coil is described as F-grade insulated copper wire with glass fiber and epoxy resin.

Epoxy resin on that coil is described as self-extinguishing, as not sustaining combustion, and as not producing toxic gases. That is the page’s materials wording.

After winding, resin seals the low-voltage foil, with DMD insulation between layers. The core is oriented cold-rolled silicon steel with a full diagonal joint. Cooling on the page is a temperature-control device with a malfunction alarm, an over-temperature alarm, an over-temperature trip, and three-phase inspection, plus a cross-flow top-blowing cooling fan.

The SC(B)10 application paragraph is a different statement. It says the resin-insulated dry-type is designed on a DuPont NOMEX paper insulation system, and it mentions German MKM copper foil for high buildings, airports, substations, commercial centers, and places described as anti-fire, anti-explode, and anti-moisture.

NOMEX paper in that paragraph is separate from the epoxy cast high-voltage sentence. The page contains both descriptions, and they stay unresolved rather than folded into one insulation system.

Three labels on the same page stay distinct. SC(B)10 is the application paragraph. SC(B)11 is the first technical table.

SC(B)13 is the second technical table. The only loss row quoted here is the SC(B)11 row.

The published high-voltage values on that table are 6, 6.3, 6.6, 10, 10.5, and 11 kV, the low voltage is 0.4 kV, and the connection groups are Dyn11 / Yyn0.

The insulation class of dry type transformer shows up here only as printed column titles, not as a decoded class code. On the SC(B)11 table, the 30 kVA row lists a no-load loss of 170 W, load-loss figures of 670 W, 710 W, and 760 W under the printed headers 130(B)100, 155(F)120, and 180(H)145, a no-load current of 2.0%, and an impedance voltage of 4.0%.

Published indoor service lists a highest air temperature of +40°C, a lowest air temperature of −5°C, a hottest monthly average of +30°C, a hottest yearly average of +20°C, and height above sea level below 1000 m. A drawing title on the page reads “IP20 with Shell.” That title names the drawing.

Series Rated capacity No-load loss Load loss 130(B)100 Load loss 155(F)120 Load loss 180(H)145 No-load current Impedance voltage
SC(B)11 30 kVA 170 W 670 W 710 W 760 W 2.0% 4.0%

If the spec is an indoor cast-style unit in this voltage band, the coil description and that single SC(B)11 row are the parts to read. The page does not catalog an open-wound model or a VPI model. When the room calls for an exposed winding or for a VPI coil, this series is the wrong example.

FAQ

What is another name for a dry-type transformer?

Air-cooled and non-liquid-filled name the category, the unit with no oil bath. Cast resin names only a coil that was actually cast. Using cast resin as the nickname for every dry-type unit erases VPI and open-wound.

How is a cast resin dry-type different from a VPI dry-type?

A cast coil is a solid encapsulated block. A VPI coil is impregnated, the outer surface is sealed, and the structure still ventilates. They are different windings, even when both sit in indoor rooms.

What is an open-wound dry-type transformer?

It is a varnish-coated winding left open to air, usually discussed for cleaner indoor rooms. Practitioners warn that open windings take up moisture. That warning is field language, not a lab curve.

Are ventilated, encapsulated, and TENV the same as cast resin and VPI?

No. Ventilated, encapsulated, and TENV describe enclosure and cooling. Cast resin and VPI describe the coil.

A vented cabinet can hold more than one winding. A sealed cabinet does not by itself mean the coil was cast.

Is IS 11171 a type of dry-type transformer?

No. IS 11171 is an Indian standard number for dry-type power transformers whose core and windings are not immersed in oil. It is not a construction family, and it is not a listing printed for the SCB series.

What are the two types of three-phase transformers?

Core-type and shell-type. That pair is magnetic-circuit construction, about where the core sits relative to the windings. It does not tell cast resin from VPI or from an open winding.

Where does a 6–10 kV SCB unit sit among those types?

The published page is a resin and cast high-voltage coil example, with a foil low-voltage winding sealed in resin. The SC(B)10 NOMEX sentence stays separate from the epoxy coil sentence. The page does not catalog open-wound or VPI.

What are the four main types of transformers?

Power, distribution, instrument, and autotransformer. That is a different taxonomy, about the job of the transformer in the system. Inside a dry-type distribution unit, the winding question is still cast resin, VPI, or open-wound.

References